Thread Rating:
  • 289 Vote(s) - 2.62 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Radio control
#1
I have just fitted my gates, and started the gate controllers, I have started the teach function for the gate operation, and completed it as per the instructions, the gates work, the photo sensors work.

I then tried to programme the key fob controllers, pressed CH1, button on the key fob, LED flashes, so the key fob works, do CH2 in the same way, learn programme completes the sequence.

However, the key fob won't work, the photo cells are working, so I am now stuck
/
any ideas?
Reply
#2
Hi Colin,
Make sure your stop circuit is linked out.Im not sure which control board you are using but you need to connect a link between the pin labelled "Stop" and the pin labelled "Com". On the CB11 these pins are labelled 19 and 20.

Hope this helps.
Steven
Gate Automation and Access Control from EasyGates Retail Store

EasyGates Trade Store for Trade only

Smart Home Tech from The Smart and Secure Centre

Smart Home News from Smart Home Matters
Reply
#3
I have fitted sub300 gate closers and a cb11 controll box one set of photo cells everthing is working and set up but they wont with remote control
Reply
#4
I have fitted sub300 gate closers and a cb11 controll box one set of photo cells everthing is working and set up but they wont with remote control
Reply
#5
David Brisland Wrote:I have fitted sub300 gate closers and a cb11 controll box one set of photo cells everthing is working and set up but they wont with remote control

Hi, Have you set up the photocells? you do this by turning the power off, placing a jumper over the terminals labelled "Save Fail Safe Photocells", then turning the power back on and removing the jumper after 15 seconds.

Check the "Stop" circuit is connected, there should be a link between "Stop" and "Com".

Also check your radio board is plugged into the CB11.

Hope this helps,
Gate Automation and Access Control from EasyGates Retail Store

EasyGates Trade Store for Trade only

Smart Home Tech from The Smart and Secure Centre

Smart Home News from Smart Home Matters
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  New enclosure for existing control panel BenH 0 579 05-06-2024, 12:49 AM
Last Post: BenH
  Fried control board nickfr 3 1,604 22-03-2024, 12:53 PM
Last Post: JoeF
  Computer controlled control panel dsbhachu1 0 766 18-02-2024, 11:35 AM
Last Post: dsbhachu1
  TC fault code on Q60ar control board Skydive1710 3 5,104 20-11-2023, 03:12 PM
Last Post: NormanY
  Control Unit CLB202 Gate leaf learning issue Kaala1 0 4,059 25-05-2023, 03:55 PM
Last Post: Kaala1
  Nice Robus RB100 - Control Board Buttons Not Working sl991 5 5,801 02-12-2022, 02:51 PM
Last Post: JoeF
  CAM ZA3 Single control board Rookie 1 8,150 13-04-2022, 11:37 AM
Last Post: JoeF
  q60 ar control panel markythesparky 0 2,108 13-11-2021, 06:21 PM
Last Post: markythesparky
  455d FAAC FUSE IN CONTROL PANEL wildfig 0 2,516 04-10-2021, 02:34 PM
Last Post: wildfig
  Genius Brain 17 Control Board - External Open/Close Signal rhennessysummit 1 5,837 02-05-2021, 09:00 PM
Last Post: soother

Forum Jump:


Users browsing this thread: 1 Guest(s)