You are not logged in or registered. Please login or register to use the full functionality of this board...


Post Reply 
 
Thread Rating:
  • 9 Votes - 1.89 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Recommend This Post:
MC424 - close automatically once open
02-12-2017, 04:11 PM
Post: #1
MC424 - close automatically once open
Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek
Find all posts by this user
Quote this message in a reply
02-12-2017, 10:43 PM
Post: #2
RE: MC424 - close automatically once open
(02-12-2017 04:11 PM)maaarek Wrote:  Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek

hi


if that issue will hapen again ,check diagnostic led P2 follow manual .

slow down engines speed , thats my suggestion
Visit this user's website Find all posts by this user
Quote this message in a reply
02-12-2017, 11:06 PM
Post: #3
RE: MC424 - close automatically once open
(02-12-2017 10:43 PM)Automatic-TC Wrote:  
(02-12-2017 04:11 PM)maaarek Wrote:  Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek

hi


if that issue will hapen again ,check diagnostic led P2 follow manual .

slow down engines speed , thats my suggestion

Hi Automatic-TC,

it is always with this incorrect behavior. I will check it tomorrow with lower speed and diagnostics.
When exactly i should see diagnostic led blinking? Once system is restarted? Or how to enter diagnostic menu? Or do i undestand it correctly that i should be watching this diagnostic led (P2) during opening of Gate?

One additional question. I understand others, but any idea what does it mean in manual in diagnostic section "M1/2 current sensitivity device triggering"?

Marek
Find all posts by this user
Quote this message in a reply
03-12-2017, 10:35 AM
Post: #4
RE: MC424 - close automatically once open
(02-12-2017 11:06 PM)maaarek Wrote:  
(02-12-2017 10:43 PM)Automatic-TC Wrote:  
(02-12-2017 04:11 PM)maaarek Wrote:  Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek

hi


if that issue will hapen again ,check diagnostic led P2 follow manual .

slow down engines speed , thats my suggestion

Hi Automatic-TC,

it is always with this incorrect behavior. I will check it tomorrow with lower speed and diagnostics.
When exactly i should see diagnostic led blinking? Once system is restarted? Or how to enter diagnostic menu? Or do i undestand it correctly that i should be watching this diagnostic led (P2) during opening of Gate?

One additional question. I understand others, but any idea what does it mean in manual in diagnostic section "M1/2 current sensitivity device triggering"?

Marek

hi

watch control board all time than hit the button .. i think that could by amperometric issue with engine . slowing down engine speed should help

regards
Tom
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  ORNO Video Doorphone -> NICE MC424 askoba 1 742 19-04-2017 06:52 AM
Last Post: Automatic-TC
  Gates open as soon as they close Craigp 4 1,090 08-01-2017 05:04 PM
Last Post: Craigp
  Installing Nice photo sensors MC424 polomint 2 1,907 06-08-2016 03:10 PM
Last Post: polomint
  Nice Mindy - One gate doesn't open Danseri 1 1,684 19-01-2016 11:00 AM
Last Post: Sav
  Use MC424 without photocell bullyx 1 2,449 02-08-2015 03:37 PM
Last Post: jaydev
  Nice MC424 control box interface to intercom access polomint 2 3,941 05-11-2012 05:36 PM
Last Post: polomint

Forum Jump: